How to lay LSD (100 hits) Blotter : LSD | Torhoo darknet markets
HOW TO LAY 100 BLOTTERS
I'm going to explain a simple way to lay LSD blotters.
[img]http://www.upload.ee/image/5358035/1.JPG[/img]
Suggested Materials:
Vodka
Raw LSD (or any other chemical)
Syringe or Eye dropper
Glass
Blotter paper
Black light
Mixing container & mixer
If you are looking for blotter paper try to find...
Key-z (clearnet)
This guy has quite a selection for blotters and gives a good price if you need a bunch. 1/4" x 1/4" perforated squares. The only downside is he has a steep price for custom prints and everything I have seen from him only has print on one side.
Printopia (darknet)
He gave me a sample of his blotters, they seemed identical to the ones I often get from key-z. I believe he also offers double sided prints.
Beginner Tips
If this is the first time you are laying blotter I would try doing this whole example without any acid, instead put a drop of food coloring into your mixture. This will allow you to see how evenly you can lay the blotter under full light.
YOU NEED TO KNOW YOUR PAPER. Even if you know you can lay your blotters evenly it is very important that you know how much liquid your paper is going to absorb! Just lay out the number of blotters you intent to lay and do not use any acid. This is a good chance to practice how you want to lay your sheet. To test how much liquid you need to use follow all of the steps below, and once you have soaked all the blotters do not let them dry and lift them off the glass. If you see any liquid underneath you are using too much liquid, if you lay acid like this you may end up with hot spots. You want just enough water that you can soak every millimeter of the paper.
If you want a starting point, my key-z paper will absorb 1ml in 100 blotters and I use 10ml in 900 blotters.
How to lay LSD (100 hits)
Clean all your surfaces and utensils.
Lay a piece of glass on top of your table. Always lay the picture face down, if you have pictures on both sides you should lay the glossy side down.
Mix your LSD in with the vodka, right now I have 11mg dilluted in 1ml of vodka. If I lay more than 100 hits I prefer to use a syringe. Sometimes LSD can be in small salt-like chunks, its very important that you beak it up until your solution is clear and well mixed even if you have to mash it with a magnetic stir stick for 20 minutes.
[img]http://www.upload.ee/image/5358052/2.JPG[/img]
Know the pattern you are laying in, you should always lay some blotters without LSD before trying a new type of blotter paper or even if you are laying more hits then you normally do.
[img]http://www.upload.ee/image/5358053/3.JPG[/img]
I am going to take half (0.5ml) of my solution and put it into my eye dropper. I will use this to lay along each blotter vertically.
[img]http://www.upload.ee/image/5358056/4.JPG[/img]
[img]http://www.upload.ee/image/5358058/5.JPG[/img]
Its difficult to see in these pictures, but once I have ran over all 100 blotters I should have 0.1-0.2ml left in the dropper. I use it to run over any blotters that did not have quite as much solution on them. No worries if it is a little unevenly laid at this point I still have over half my solution left.
[img]http://www.upload.ee/image/5358059/6.JPG[/img]
Now I take the rest of my solution and start to lay it the blotters horizontally in the same pattern I did before.
[img]http://www.upload.ee/image/5358062/7.JPG[/img]
Once I have gone across all my blotters horizontally it starts to look pretty good, I use any remaining mixture to fill in any pieces and edges of blotters that are still dry. If you know how much liquid you need you should always have enough to soak every blotter.
[img]http://www.upload.ee/image/5358063/8.JPG[/img]
Now if this is a test run you should check if there is any liquid under the blotters and/or change the amount you are using accordingly. Make sure you have at least one good test sheet, using food coloring is an excellent way to see how evenly you have laid the blotters.
If this is your actual sheet of LSD do not remove the blotters from the glass, instead place the sheet in a cool dark place for 1+ hours before removing from the glass. I let my blotters dry in the air for a few hours before sealing it up or attempting to rip a page apart.
It's a good idea to look at your sheet under a black light, you can see the nice even lay glowing above the regular paper I have my hits on.
[img]http://www.upload.ee/image/5358074/9.JPG[/img]
Here is my final dry product
[img]http://www.upload.ee/image/5358076/10.JPG[/img]
