{TUTORIAL} How to create a proper volumetric solution with your alrazolam ( xanax ) powder : Xanax | Torhoo darknet markets
Alprazolam also known as Xanax when sold in its raw form is extremely powerful and even more so dangerous if handled inappropriately. The consequences of mishandling this compound can be catastrophic in nature. It can ruin your or some one elses life + end your life or some one elses life + end with you or some one else in jail for having done some thing you regret and probably do not remember.
In the pharmaceutical world in the USA Alprazolam is prescribed in the following increments-
0.25 mg (white pill)
0.5 mg (peach or orange pill)
1 mg (blue pill)
2 mg (known as a bar or ladder commonly segmented in to 4 proportional portions of 0.5mg each)
The real danger lies in the fact that most people do not accurately under stand the concept of weight and they do not have the appropriate scales to determine them. This creates situations where people consume far too much of the compound and black out which creates disastrous scenarios.
1mg for reference is comparable to a grain or 2 of table salt. Let that sink in a moment.........
Lets make a solution that allows you to use your pure pharma grade alprazolam powder safe and responsibly. Do not be one of those ass holes that does not care about the end use or user.
To make a solution you will need a few things. You will need-
- High proof liquor such as Everclear or Golden Grain (190 Proof/95% Alcohol, in some states everclear and golden grain is a lower proof so be aware of this), Bacardi 151, or some 100 Proof vodka.
- A syringe or pipette to measure your liquid (needled syringe or medicine syringe works fine. You can buy these pretty much anywhere meds are sold). Seek equipment with clearly marked denominations such as 0.05ml increments.
- A small glass container (Make sure your syringe or pipette can fit down inside to suck the solution up)
- OPTIONAL- Graduated cylinder to measure your liquid out. If you want to skip this, you can use your pipette or syringe, but MAKE SURE YOU MEASURE CORRECTLY!!!!! Do not miscount!!!!
For this tutorial we are going to assume that you have 50mg of powder and want to make a solution that is 1mg per 0.25ml. {TIP- liquor stores sell measured amounts of liquor like a shot 50ml, double shot 100ml and on up so think of this if you are having trouble with measurements the volume is listed on the bottle}
To figure out how much liquid you are going to need you are going to multiply 50mg by 0.25ml which gives you 12.5. This means that you are going to measure out 12.5ml of the high proof alcohol and place it into your small glass container.
Once the correct amount of alcohol is in the container put your powder into the container with the alcohol. Make sure you get it all in there and do not spill any. Be patient and do not rush or you will spill it.
Once all of the powder is in there you will want to cap it off (try to avoid caps with a paper lining in the top as it will absorb liquid and ruin your ratios). Once you cap it off shake it for a couple minutes while making sure everything is dissolved perfectly. If you are having trouble making it all dissolve you can get a cup of hot water and put the glass container in there to heat the alcohol up a bit. Once the alcohol warms up some, shake it a bit more. You should have no problems after this. BE AWARE THAT ALCOHOL EVAPORATES VERY FAST ESPECIALLY WHEN HEATED. ALWAYS KEEP YOUR SOLUTION AIR TIGHT AT ALL TIMES UNTIL YOU ARE DOSING. IF EVAPORATION OCCURS YOU WILL OFF SET YOUR RATIOS AND END UP WITH A MUCH MORE CONCENTRATED SOLUTION.
You are done!! It is time to dose your self or friend or customer or item!! This netted you 1mg of powder per 0.25ml of liquid. You can change this up if you would like to. If you have 50mg powder and want 1mg per 0.5ml, you just times 50 by 0.5, which is 25. You would then dissolve the powder in 25ml of liquid to get 1mg per 0.5ml of liquid. If you are having trouble with the math send me a message or reply here and I will help you.
Good luck, be safe, educate yourself, and STAY FREE. If you have any questions at any time please remember that I am here. I will answer any and all questions once i read them. With out you guys I am nothing. If I sell you drugs, I want to help make sure you do them properly and that you safely distribute to your customers. Safety is important. You only have one life to live do not ruin it by being impatient or by not being compassionate.
Thank you very much for your business and for reading :-).
you are welcome. if we sell this to people we have to assume some level of responsibility to try to ensure that it is reaching educated hands in order to optimize the chance that it is being consumed in a safe and responsible manner.
alcohol aka EToH (ethanol the kind of alcohol that is in liquor) is also a good medium for creating a solution with alprazolam. it is much easier to access and due to the volumes that it is sold in it a readily available medium to create a accurate solution :-).
yes i agree this would be a good sticky. harm reduction is very important. i am not a fan of pressed pills. i have heard too many horror stories of people dying due to different compounds being in the pills and i have heard of people being ripped off constantly.
proper liquid solutions are a great remedy for these problems. if a concentrated enough solution is created wtih high proof ethanol you can also dose small items very accurately with a pipette.